Description
OBD-II Trouble Code Description for P0210 Hyundai
Injector Circuit/Open – Cylinder 10
What does this mean?
OBD2 Code P0210 Hyundai definition:
P0208 Hyundai means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of OBD code P0210 Hyundai
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Causes
Possible causes of OBD code P0210 Hyundai
The causes of a P0208 Hyundai engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
The OBD2 Code Information Be Applicable For Hyundai:
2013 Hyundai i30,2013 Hyundai i20,2013 Hyundai Santa Fe,2013 Hyundai Langdong,2013 Hyundai HB20X,2013 Hyundai HB20S,2013 Hyundai HB20,2012 Hyundai i40,2011 Hyundai ix35,2011 Hyundai ix20,2011 Hyundai i10,2011 Hyundai Verna,2011 Hyundai Sonata,2011 Hyundai Azera,2011 Hyundai Avante,2010 Hyundai Accent,2009 Hyundai ix55,2009 Hyundai i20,2009 Hyundai Sonata,2008 Hyundai i800,2008 Hyundai i30,2008 Hyundai i10,2007 Hyundai Veracruz,2007 Hyundai Elantra,2007 Hyundai Coupe,2006 Hyundai Getz,2005 Hyundai Tucson,2005 Hyundai Trajet,2005 Hyundai Terracan,2005 Hyundai Sonata,2005 Hyundai Santa Fe,2005 Hyundai Portico Concept,2005 Hyundai Matrix,2005 Hyundai HED 1 Concept,2005 Hyundai Grandeur,2005 Hyundai Getz,2005 Hyundai Coupe,2004 Hyundai HCD8 Concept,2004 Hyundai Elantra,2004 Hyundai E-Cubed Concept,2004 Hyundai Atos Prime,2004 Hyundai Accent,2003 Hyundai CCS Concept,2002 Hyundai HCD 7 Concept,2001 Hyundai HCD 6 Concept
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Hyundai makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.