Description
OBD-II Trouble Code Description for P0335 Nissan
Crankshaft Position Sensor “A” Circuit
What does this mean?
OBD2 Code P0335 Nissan definition:
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 Nissan will set.
Symptoms
Possible sumptoms of OBD code P0335 Nissan
NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include: Vehicle may not start (see above) Vehicle may run rough or misfire MIL illumination
Causes
Possible causes of OBD code P0335 Nissan
Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Broken timing belt Failed PCM
Possible Solutions
Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there’s no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn’t be performed if you’re not familiar with automobile electrical systems). Is the sensor within resistance specs? If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay? If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.
The OBD2 Code Information Be Applicable For Nissan:
2013 Nissan Pathfinder,2013 Nissan Murano,2013 Nissan Juke Nismo,2013 Nissan GT-R,2013 Nissan Altima Sedan,2013 Nissan Almera,2013 Nissan 370Z,2012 Nissan Tiida,2012 Nissan Sunny,2012 Nissan Qashqai,2012 Nissan Murano,2012 Nissan Micra ELLE,2012 Nissan Micra DIG-S,2012 Nissan Maxima,2012 Nissan Juke Shiro,2012 Nissan GT-R,2012 Nissan Extrem Concept,2011 Nissan X-Trail,2011 Nissan Rogue,2011 Nissan Quest,2011 Nissan Pivo 3 Concept,2011 Nissan Patrol,2011 Nissan Murano,2011 Nissan Micra,2011 Nissan LEAF,2011 Nissan Juke,2011 Nissan GT-R,2011 Nissan 370Z,2010 Nissan Qashqai,2010 Nissan Pathfinder,2010 Nissan Navara,2010 Nissan NV200,2010 Nissan GT-R SpecV,2010 Nissan Cube,2010 Nissan Altima Sedan,2010 Nissan Altima Coupe,2010 Nissan 370Z Roadster,2009 Nissan Xterra,2009 Nissan Pixo,2009 Nissan Note,2009 Nissan Murano,2009 Nissan Maxima,2009 Nissan Frontier,2009 Nissan 370Z,2008 Nissan X-Trail,2008 Nissan Rogue,2008 Nissan Pathfinder,2008 Nissan GT-R,2007 Nissan Sentra SE-R,2007 Nissan Mixim,2007 Nissan Altima,2006 Nissan Urge Concept,2006 Nissan Note,2006 Nissan 350Z,2005 Nissan Zaroot Concept,2005 Nissan Xterra,2005 Nissan Terrano,2005 Nissan Sport Concept,2005 Nissan Primera,2005 Nissan Pivo Concept,2005 Nissan Pickup,2005 Nissan Patrol,2005 Nissan Pathfinder,2005 Nissan Micra,2005 Nissan Altima,2004 Nissan Titan,2004 Nissan Tiida
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Nissan makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.