P0356 Acura Ignition Coil 6 Primary/Secondary Circuit

Description

OBD-II Trouble Code Description for P0356 Acura

Ignition Coil “F” Primary/Secondary Circuit

What does this mean?

OBD2 Code P0356 Acura definition:
The COP (coil on plug) ignition system is what is used on most modern engines. There is an individual coil for each cylinder that is controlled by the PCM (powertrain control module). It eliminates the need for spark plug wires by putting the coil right above the sparkplug. Two wires are dedicated to each coil. One is a battery feed usually from the power distribution center. The other wire is the coil driver circuit from the PCM. The PCM grounds/ungrounds this circuit to activate or deactivate the coil. The coil driver circuit is monitored by the PCM for faults If an open or a short is detected in the driver circuit for coil number 6, a P0356 Acura may set. Also, depending on the vehicle, the PCM may also shut down the fuel injector to the cylinder also.

Symptoms

Possible sumptoms of OBD code P0356 Acura
MIL (Malfunction indicator lamp) illumination Engine misfire may be present or intermittent

Causes

Possible causes of OBD code P0356 Acura
Short to voltage or ground on COP driver circuit Open on COP driver circuit Loose connection at coil or broken connector locks Bad Coil (COP) Faulty Powertrain Control Module

Possible Solutions

Is the engine misfiring presently? If not, the problem is likely intermittent. Try wiggle testing the wiring at the #3 coil and along the wiring harness to the PCM. If manipulating the wiring causes the misfire to surface, repair the wiring problem. Check for poor connection at the coil connector. Verify the harness isn’t misrouted or chafing on anything. Repair as necessary If the engine is misfiring presently, stop the engine and disconnect the #3 coil wiring connector. Then start the engine and check for a driver signal to the #3 coil. Using a scope will give you a visual pattern to observe, but since most people don’t have access to one there’s an easier way. Use a Voltmeter in AC Hertz scale and see if there’s a Hz reading of between 5 and 20 or so that indicates the driver is working. If there is a Hertz signal, then replace the #3 ignition coil. It’s likely bad. If you don’t detect any frequency signal from the PCM on the ignition coil driver circuit indicating the PCM is grounding/ungrounding the circuit (or there is no visible pattern on the scope if you have one) then leave the coil disconnected and check for DC voltage on the driver circuit at the ignition coil connector. If there is any significant voltage on that wire then there is a short to voltage somewhere. Find the short and repair it. If there is no voltage on the driver circuit, then turn the ignition off. Disconnect the PCM connector and check the continuity of the driver between the PCM and the coil. If there is no continuity repair the open or short to ground in the circuit. If continuity is present, then check for resistance between ground and the ignition coil connector. There should be infinite resistance. If there isn’t, repair the short to ground in the coil driver circuit NOTE: If the ignition coil driver signal wire is not open or shorted to voltage or ground and there is no trigger signal to the coil then suspect a faulty PCM coil driver. Also keep in mind that if the PCM driver is at fault, there may be a wiring problem that caused the PCM failure. It’s a good idea to do the above check after PCM replacement to verify there won’t be a repeat failure. If you find that the engine isn’t misfiring, the coil is being triggered properly but P0353 Acura is continually being reset, there is the possibility that the PCM coil monitoring system may be faulty.

The OBD2 Code Information Be Applicable For Acura:

2014 Acura RLX,2014 Acura MDX,2013 Acura SUV-X Concept,2013 Acura RDX,2013 Acura NSX Concept,2013 Acura MDX Concept,2013 Acura ILX Endurance Racer,2013 Acura ILX,2012 Acura TL,2012 Acura RLX Concept,2012 Acura NSX Concept,2012 Acura ILX Street Build Concept,2012 Acura ILX Concept,2011 Acura TSX Sport Wagon,2011 Acura TSX Sedan,2010 Acura ZDX,2010 Acura TSX V6,2010 Acura RDX,2010 Acura MDX,2009 Acura ZDX Concept,2009 Acura TSX,2009 Acura TL,2009 Acura RL,2007 Acura TSX,2007 Acura TL Type-S,2007 Acura TL,2007 Acura RDX,2007 Acura MDX,2007 Acura Advanced Sports Car Concept,2006 Acura RDX Prototype,2006 Acura MD-X Concept,2006 Acura Advanced Sedan Concept,2005 Acura TSX A-Spec Concept,2005 Acura TSX,2005 Acura TL,2005 Acura RSX Type-S,2005 Acura RSX A-Spec Concept,2005 Acura RSX,2005 Acura RL with ASPEC Performance Package,2005 Acura RL ASPEC Concept,2005 Acura RL,2005 Acura RDX Concept,2005 Acura NSX,2005 Acura MDX,2004 Acura TL with ASPEC Performance Package,2004 Acura TL 25 Hours of Thunderhill,2004 Acura RL Prototype,2004 Acura 3.2 TL,2003 Acura TL ASPEC Concept,2003 Acura 3.2 CL Type-S,2002 Acura NSX sketches,2001 Acura NSX-T,2001 Acura Integra

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Acura makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.