Description
OBD-II Trouble Code Description for P0116 Porsche
Engine Coolant Temperature Circuit Range/Performance
What does this mean?
OBD2 Code P0116 Porsche definition:
The ECT (Engine coolant temperature) sensor is a thermistor which changes resistance based on temperature of the coolant in contact with it. The ECT sensor will be located in the block or coolant passage. Usually it is a two wire sensor. One wire is a 5 Volt supply from the PCM (Powertrain Control Module) to the ECT. The other is a ground to the ECT.
As the temperature of the coolant changes the resistance on the signal wire changes accordingly. The PCM monitors the reading and determines coolant temperature in order to perform essential engine fuel management. When engine coolant is low, sensor resistance is high. The PCM will see a high signal voltage (low temperature). When coolant is warm, the sensor’s resistance is low and the PCM will see a high temperature. The PCM expects to see slow resistance changes on the ECT signal circuit. If it sees a quick change in voltage that isn’t consistent with an engine warming up, this P0116 Porsche code will set. Or if it sees a lack of change in ECT signal, this code may set.
Symptoms
Possible sumptoms of OBD code P0116 Porsche
There may be no noticeable symptoms if the problem is very intermittent, however the following may occur: MIL (Malfunction Indicator Lamp) illumination Poor drivability Black smoke at tailpipe Poor fuel economy May not idle May exhibit stalling or misfires
Causes
Possible causes of OBD code P0116 Porsche
Potential causes of the P0116 Porsche code include: Missing or stuck-open thermostat Bad ECT sensor Short or open on signal wire Short or open on ground wire Poor connections in wiring
Possible Solutions
If there are any other ECT sensor codes, diagnose them first. Using a scan tool, check the ECT reading. On a cold engine, it should match the IAT reading or should be equal to ambient (outside) temperature reading. If it does match the IAT or ambient temp, check the freeze frame data on your scan tool (if equipped). The saved data should tell you what the ECT reading was when the fault occurred. A) If the saved info indicates that the engine coolant reading was at the coldest exreme (around -30 deg. F) then that’s a good indication the ECT resistance was intermittently high (unless you live in Anchorage!) Check for an open in the ECT sensor ground and signal circuits and repair as necessary. If they appear okay, warm the engine up while monitoring the ECT for any intermittent jumps high or low. If there are replace the ECT. B) If the saved info indicates that the engine coolant reading was at the warmest exreme (around 250+ deg.F) then that’s a good indication the ECT resistance was intermittently low. Check for a short to ground on the signal circuit and repair as necessary. If it appears okay, warm the engine up while monitoring the ECT for any intermittent jumps high or low. If there are replace the ECT.
The OBD2 Code Information Be Applicable For Porsche:
2013 Porsche Cayenne,2013 Porsche Boxster S,2013 Porsche Boxster,2013 Porsche 911,2012 Porsche Panamera,2012 Porsche 911,2011 Porsche 911,2010 Porsche Panamera,2010 Porsche Cayenne,2010 Porsche 911 GT3,2009 Porsche 911,2008 Porsche Cayenne,2008 Porsche Boxster,2008 Porsche 911,2007 Porsche Cayman,2007 Porsche Cayman,2007 Porsche Boxster,2007 Porsche Boxster,2007 Porsche 911,2006 Porsche 911,2005 Porsche Boxster S,2005 Porsche Boxster,2005 Porsche 911,2004 Porsche 911,2003 Porsche 911
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Porsche makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.