Toyota P0335 Crankshaft Position Sensor A Circuit Malfunction

Description

OBD-II Trouble Code Description for P0335 Toyota

Crankshaft Position Sensor “A” Circuit

What does this mean?

OBD2 Code P0335 Toyota definition:
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 Toyota will set.

Symptoms

Possible sumptoms of OBD code P0335 Toyota
NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include: Vehicle may not start (see above) Vehicle may run rough or misfire MIL illumination

Causes

Possible causes of OBD code P0335 Toyota
Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Broken timing belt Failed PCM

Possible Solutions

Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there’s no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn’t be performed if you’re not familiar with automobile electrical systems). Is the sensor within resistance specs? If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay? If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

Related Codes

P0385 Toyota P0335 Toyota P0385 Toyota P0016 Toyota P0017 Toyota P0018 Toyota P0019 Toyota P0335 Toyota P0336 Toyota P0337 Toyota P0338 Toyota P0339 Toyota P0385 Toyota P0386 Toyota P0387 Toyota P0388 Toyota P0389 Toyota


The OBD2 Code Information Be Applicable For Toyota:

2013 Toyota Auris,2012 Toyota Yaris,2012 Toyota Verso-S,2012 Toyota Tacoma,2012 Toyota Prius V,2012 Toyota Prius C,2012 Toyota Prius,2012 Toyota Hilux,2012 Toyota Camry,2012 Toyota Avensis,2012 Toyota Aurion,2012 Toyota 86 GTS,2011 Toyota Tacoma,2011 Toyota Sienna,2011 Toyota Sequoia,2011 Toyota RAV4,2011 Toyota Matrix,2011 Toyota Highlander,2011 Toyota Corolla,2011 Toyota Avalon,2011 Toyota Auris HSD,2010 Toyota iQ3,2010 Toyota Yaris,2010 Toyota Verso,2010 Toyota Tundra,2010 Toyota Prius,2010 Toyota Land Cruiser,2010 Toyota Corolla,2010 Toyota Camry,2010 Toyota Auris,2010 Toyota 4Runner,2009 Toyota iQ,2009 Toyota Yaris,2009 Toyota Venza,2009 Toyota RAV4,2009 Toyota Matrix,2009 Toyota Hilux,2009 Toyota Aygo,2009 Toyota Avensis,2009 Toyota Aurion,2009 Toyota 4Runner,2008 Toyota Sequoia,2007 Toyota Tundra,2007 Toyota Avensis,2006 Toyota RAV4,2006 Toyota Aurion,2005 Toyota Corolla Sedan,2004 Toyota Prius,2004 Toyota Corolla,2003 Toyota RAV4,2003 Toyota Land Cruiser,2003 Toyota Celica

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Toyota makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.